Overview

SDV-CTRX-BD – SDVoE Full 4K 10G AV over IP Bi-directional Transceiver with USB Extension

The SDV-CTRX-BD 10G SDVoE transceiver is designed for high-quality, IP routable, AV extension with minimum latency for the SDVoE range of 10G AV over IP. The SDV-CTRX-BD Transceiver is capable of simultaneous bi-directional AV extension, enhancing the flexibility of any installation. By using a sophisticated ultra-light compression scheme (lossless for most content) it’s a great solution for extending 4K audio/video streams (HDMI or Display Port) and data.

Advanced HDMI content such as HDR (High Dynamic Range), 10-bit colour and multi-channel HD Bitstream audio can be transmitted in pass-through mode. The use of high quality 10 Gigabit Ethernet ports and Cat.6 (Cat.6a recommended) cable allows for point-to-point transmission of the video signal up to 100m. Multiple control and data signals may also be transmitted along with the audio and video, including IR, RS-232, USB 2.0, and Ethernet.

When combined with the optional IP Master Controller (SDV-CS8), the functionality of the Transceiver expands exponentially. Multiple Transceivers or SDVoE TX/RXs may be combined with one or more 10-Gigabit Ethernet switches and the units can be used together to form a distributed video matrix, with multi-view and video wall configuration adding to their flexibility in large event installations.

The integrated USB hub of each Transceiver can function as a simple point to point KVM extension or freely routed between any two endpoints. This type of USB KVM routing flexibility enables a wide range of multi-user, control room, or on-demand installation scenarios. The built-in EDID and HDCP management functionality enables the unit to fit into every situation.

A specialised use of the SDV-CTRX-BD is for the creation of true multi-view signals within a video wall arrangement, simply add one SDV-CTRX-BD to any SDVoE system and through its bi-directional nature any user can simply directly connect the HDMI I/O, setting up the receiver side to a Multi-view arrangement and routing the transmitter side onto any video wall arrangement, saving having to purchase very expensive video wall processors.

Basic configuration of the unit can be achieved via front panel buttons with an OSD (On-Screen Display). Advanced control requires the optional IP Master Controller (SDV-CS8).

  • HDMI 2.0 and DVI 1.0 compatible
  • HDCP 2.2 and HDCP 1.x compliant
  • 1 HDMI and 1 DisplayPort input
  • 1 HDMI output
  • 1 analog stereo input & 1 analog stereo output
  • 2 USB 2.0 (Type-A) ports and 1 USB 2.0 (Mini-B) port
  • Transceiver supports simultaneous bi-directional AV signal extension
  • IP switchable with minimum latency
  • Ultra-light compression, lossless for most content
  • Extension up to 100m in Point-to-Point or 10G IP matrix mode
  • Supports independent breakaway A/V matrix switching with minimal latency, video wall generation, and multiview compositing (requires SDV-CS8)
  • Supports pass-through of 10/12-bit HDR sources
  • Supports pass-through of audio formats including LPCM (up to 8 channels), Bitstream and HD Bitstream from HDMI or DP sources
  • Analog stereo audio extension, insertion and extraction (insertion and extraction requires optional IP Master Controller, the SDV-CS8)
  • Bi-directional AV, IR, RS-232, USB 2.0, and Ethernet extension
  • Supports a special Simultaneous Mode for USB extension allowing a host connected to a single transceiver to connect to up to 7 transceivers with USB devices connected (Mass storage devices are not supported in this mode. Requires optional IP Master Controller)
  • Unit can be powered directly by PoE when connected to a 10 Gigabit Ethernet (10GbE) switch that provides PoE (802.3at)
  • Basic configuration via front panel buttons with an OSD
Inputs  1x HDMI [1x HDMI Uncompressed AV and Data]
1x Display Port [1x Uncompressed AV]
1x RJ45 [1x SDVoE HDMI & Propriety Data]
1x 3.5mm Stereo mini-jack [1x Analogue Stereo(L/R)]
1x 3.5mm Stereo mini-jack [1x Infra Red Receiver]
1x Phoenix (3 pin) [1x RS-232]
1x RJ45 [1x LAN Serving]
1x USB Mini B [1x USB host & service port Propriety Data]
Outputs  1x HDMI [1x HDMI Uncompressed AV and Data]
1x RJ45 [1x SDVoE (shared) HDMI & Propriety Data]
1x 3.5mm Stereo mini-jack [1x Analogue Stereo(L/R)]
1x 3.5mm Stereo mini-jack [1x Infra Red Emitter]
POE PSU PoE
PSU  12V/3A
Dimensions  231.5mm [W] x 25mm [H] x 108mm [D]
Net Weight  580g
Gross Weight  1.6kg
Product Stock Category Core Product

You may also like…

Here’s an idea for a perfect pairing...

Did you know that this product also works with the following CYP products...

SDV-C1H-RX – SDVoE Full 4K 10G AV over IP CAT-Based Small Form Factor Receiver

SDV-C1H-RX 10G SDVoE receiver  is designed for high-quality, IP routable, AV extension up to 4K@60 4:4:4 with minimum latency. SDV-C1H-RX uses 10G Ethernet ports, and Cat.6A cable to allow transmission of the video signal up to 100m. Advanced HDMI content...

SDV-C1H-TX – SDVoE Full 4K 10G AV over IP CAT-Based Small Form Factor Transmitter

SDV-C1H-TX 10G SDVoE Transmitter is designed for high-quality, IP routable, AV extension up to 4K@60 4:4:4 with minimum latency. SDV-C1H-TX utilises  10G Ethernet ports, and Cat.6A cable to allow transmission of the video signal up to 100m. Advanced HDMI content...

SDV-FTRX-BD – SDVoE Full 4K 10G AV over IP Bi-directional Fiber Based Transceiver with USB Extension

The SDV-FTRX-BD SDVoE Full 4K 10G AV over IP Bi-directional Fiber Transceiver is designed for high-quality, IP routable, AV extension with minimum latency for the SDVoE range of 10G AV over IP. The SDV-FTRX-BD SDVoE Full 4K 10G AV over...

SDV-C2-RX – SDVoE Full 4K 10G AV over IP HDMI Receiver with USB

The SDV-C2-RX SDVoE Full 4K 10G AV over IP HDMI Receiver is designed for high-quality, IP routable, AV extension over a 10G IP Network with minimum latency. By using a sophisticated ultra-light compression scheme (lossless for most content) the SDV-C2-RX...